[ Pobierz całość w formacie PDF ]
Features
•
Serial Peripheral Interface (SPI) Compatible
•
Supports SPI Modes 0 (0,0) and 3 (1,1)
•
Low-Voltage and Standard-Voltage Operation
– 5.0 (V
CC
= 4.5V to 5.5V)
– 2.7 (V
CC
= 2.7V to 5.5V)
– 1.8 (V
CC
= 1.8V to 3.6V)
•
2.1 MHz Clock Rate (5V) Compatibility
•
8-Byte Page Mode
•
Block Write Protection
– Protect 1/
4, 1/
2, or Entire Array
•
Write Protect (WP) Pin and Write Disable Instructions for
Both Hardware and Software Data Protection
•
Self-Timed Write Cycle (10 ms max)
•
High Reliability
– Endurance: 1 Million Write Cycles
– Data Retention: 100 Years
– ESD Protection: >4000V
•
Automotive Grade and Extended Temperature Devices Available
•
8-Pin PDIP and JEDEC SOIC Packages
SPI Serial
EEPROMs
1K (128 x 8)
2K (256 x 8)
4K (512 x 8)
Description
The AT25010/020/040 provides 1024/2048/4096 bits of serial electrically erasable
programmable read only memory (EEPROM) organized as 128/256/512 words of 8
bits each. The device is optimized for use in many industrial and commercial applica-
tions where low power and low voltage operation are essential. The AT25010/020/040
is available in space saving 8-pin PDIP and 8-pin JEDEC (SOIC
) pa
ckages.
The AT25010/020/040 is enabled through the Chip Select pin (CS) and accessed via
a 3-wire interface consisting of Serial Data Input (SI), Serial Data Output (SO), and
Serial Clock (SCK). All programming cycles are completely self-timed, and no sepa-
rate ERASE cycle is required before WRITE.
BLOCK WRITE protection is enabled by programming the status register with one of
four blocks of write protection. Separate program enable and program disable instruc-
tions ar
e pr
ovided for additional data protection. Hardware data pro
tection
is provided
via the WP pin to protect against inadvertent write attempts. The HOLD pin may be
used to suspend any serial communication without resetting the serial sequence.
AT25010
AT25020
AT25040
SPI, 1K Serial
E
2
PROM
Pin Configurations
8-Pin PDIP
Pin Name Function
CS
Chip Select
CS
SO
WP
GND
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
SCK
Serial Data Clock
SI
Serial Data Input
SO
Serial Data Output
GND
Ground
8-Pin SOIC
VCC
Power Supply
WP
Write Protect
CS
SO
WP
GND
1
2
3
4
8
7
6
5
VCC
HOLD
SCK
SI
HOLD
Suspends Serial Input
Rev. 0606E–08/98
1
Absolute Maximum Ratings*
Operating Temperature ................................. -55°C to + 125°C
*NOTICE: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent dam-
age to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification is not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect
device reliability.
Storage Temperature .................................... -65°C to + 150°C
Voltage on Any Pin
with Respect to Ground ....................................-1.0V to + 7.0V
Maximum Operating Voltage........................................... 6.25V
DC Output Current........................................................ 5.0 mA
Block Diagram
2
AT25010/020/040
AT25010/020/040
Pin Capacitance
(1)
Applicable over recommended operating range from T
A
= 25°C, f = 1.0 MHz, V
CC
= +5.0V (unless otherwise noted).
Symbol
Test Conditions
Max
Units
Conditions
C
OUT
Output Capacitance (SO)
8
pF
V
OUT
= 0V
C
IN
Input Capacitance (CS, SCK, SI, WP, HOLD)
6
pF
V
IN
= 0V
Note: 1. This parameter is characterized and is not 100% tested.
DC Characteristics
Applicable over recommended operating range from: T
AI
= -40°C to +85°C, V
CC
= +1.8V to +5.5V, T
AC
= 0°C to +70°C,
V
CC
= +1.8V to +5.5V (unless otherwise noted).
Symbol
Parameter
Test Condition
Min
Max
Units
V
CC1
(1)
Supply Voltage
1.8
5.5
V
V
CC2
Supply Voltage
2.7
5.5
V
V
CC3
Supply Voltage
4.5
5.5
V
I
CC1
Supply Current
V
CC
= 5.0V at 1 MHz, SO = Open
3.0
mA
I
CC2
Supply Current
V
CC
= 5.0V at 2 MHz, SO = Open
6.0
mA
I
SB1
(1)
Standby Current
V
CC
= 1.8V
CS = V
CC
100
m
A
I
SB2
Standby Current
V
CC
= 2.7V
CS = V
CC
100
m
A
I
SB3
Standby Current
V
CC
= 5.0V
CS = V
CC
100
m
A
I
IL
Input Leakage
V
IN
= 0V to V
CC
-0.6
3.0
m
A
I
OL
Output Leakage
V
IN
= 0V to V
CC
, T
AC
= 0
°
C to 70
°
C
-0.6
3.0
m
A
V
IL
(2)
Input Low Voltage
-0.6
V
CC
x 0.3
V
V
IH
(2)
Input High Voltage
V
CC
x 0.7
V
CC
+ 0.5
V
V
OL1
Output Low Voltage
I
OL
= 2.0 mA
0.4
V
4.5V
£
V
CC
£
5.5V
V
OH1
Output High Voltage
I
OH
= -1.0 mA
V
CC
- 0.8
V
V
OL2
Output Low Voltage
I
OL
= 0.15 mA
0.2
V
1.8V
£
V
CC
£
3.6V
V
OH2
Output High Voltage
I
OH
= -100
m
A
V
CC
- 0.2
V
Notes: 1. This parameter is preliminary and Atmel may change the specifications upon further characterization.
2. V
IL
min and V
IH
max are reference only and are not tested.
3
AC Characteristics
Applicable over recommended operating range from T
A
= -40°C to +85°C, V
CC
= As Specified,
CL = 1 TTL Gate and 100 pF (unless otherwise noted).
Symbol
Parameter
Voltage
Min
Max
Units
f
SCK
SCK Clock Frequency
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
2.1
2.1
0.5
MHz
t
RI
Input Rise Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
2
2
2
m
s
t
FI
Input Fall Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
2
2
2
m
s
t
WH
SCK High Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
200
200
800
ns
t
WL
SCK Low Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
200
200
800
ns
t
CS
CS High Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
250
1000
ns
t
CSS
CS Setup Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
250
1000
ns
t
CSH
CS Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
250
1000
ns
t
SU
Data In Setup Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
50
50
100
ns
t
H
Data In Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
50
100
100
ns
t
HD
Hold Setup Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
100
100
400
ns
t
CD
Hold Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
200
200
400
ns
t
V
Output Valid
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
200
400
800
ns
t
HO
Output Hold Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
ns
4
AT25010/020/040
AT25010/020/040
AC Characteristics (Continued)
Applicable over recommended operating range from T
A
= -40°C to +85°C, V
CC
= As Specified,
CL = 1 TTL Gate and 100 pF (unless otherwise noted).
Symbol
Parameter
Voltage
Min
Max
Units
t
LZ
Hold to Output Low Z
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
0
0
0
100
100
100
ns
t
HZ
Hold to Output High Z
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
100
100
100
ns
t
DIS
Output Disable Time
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
250
500
1000
ns
4.5 - 5.5
2.7 - 5.5
1.8 - 3.6
10
t
WC
Write Cycle Time
ms
Endurance
5.0V, 25
C, Page Mode
1M
Write Cycles
Note: 1. This parameter is characterized and is not 100% tested.
5
°
[ Pobierz całość w formacie PDF ]